Electrical Repair News

Five Steps to a Brand New Door Learning how to replace a door opens a whole new window of opportunity for a do-it-yourselfer. A new door can change the style of a room or brighten up the exterior of a house. In addition, a new door with a better seal can help prevent drafts and improve heating bills.

There are three types of doors: entry doors, interior doors, and combination storm/screen doors. The five steps below describe the technique for replacing an entry door. If you can master replacement of an entry door, replacing most interior doors is actually a simplified version of that process, as the locks are typically simpler or nonexistent. Replacement of combination storm/screen doors can follow the same process as that of entry doors, or it can become more complicated. If you are unsure about the process for installing a combination storm/screen door, check your manufacturer’s information for additional instructions or speak with a representative of the manufacturer or store that sold you the door. Remove the old door. To remove the old door, open it and wedge under the outer corner to take weight off the hinges. Once the door has been removed, set it aside to use as a pattern in trimming the new door unless it is seriously warped or damaged. To remove the door, follow one of the two options below. A popular method for hanging doors is the use of loose-pin hinges. With loose-pin hinges, half the hinge attaches to the door and the other half to the doorframe. Both halves are held together by a pin. If this is the type of hinge you’re dealing with, remove the pin by tapping it up and completely pulling it out. Start with the bottom hinge and work your way up. Once the hinges have been removed, you can take the door off the frame. In some older homes, a different type of hinge may be used or the pin cannot easily be removed because it has been covered by layers of paint. In this case, unscrew the hinges from the doorframe (still working from bottom to top) and remove the door. Remove hinge leaves. Remove the hinge leaves from the door and the frame. You can choose to either reuse the original hinges or hang new ones. If you reuse the original ones, you can buff them with sandpaper and spray them with a clear protective coating. For new hinges, simply insure that they are the same size as the old ones. Once you have gotten the hinges in the shape you want them, install the new hinge leaves on the door frame. Be sure your screws are long enough to pierce both the frame and the stud-wall framing. This is an extra security measure. Trim new door. If possible, use the original door as a pattern for the new one. Alight the top and side edges and see whether the new door needs to be cut down along the bottom. If you cannot use the old door as a pattern, measure the door opening and allow a 1/8" bottom clearance and 1/16" top and side clearance. If the door opens over carpet, increase the bottom clearance to 3/4" or more. Mark the appropriate dimensions on the new door. Trim the bottom of the door with a fine-toothed saw. Alternatively you can work from the corners to the center of the bottom edge with a block plane. Also use a jack plane for edge trimming if necessary. To prevent binding when the new door is opened, bevel the latch edge inward. Prepare new door for hinges. The first step in preparing the door for the hinges is to create the new mortises, which are carved or routed-out depressions where the hinge blades are placed, which keeps the surface even. Again using the old door for a pattern, mark hinge mortise locations. If you choose not to pattern after the old door, stick the new door in the opening and wedge it 1/8" from the bottom. Mark the hinge locations on the door. Next, set the door on its latch edge. Use a square and pencil or knife to draw a line across the door edge at each hinge location. Outline the new hinge on the door by using the hinge leaf as a template. Score marked edges for the hinge mortises with a wood chisel. Do not cut deeper than hinge leaf thickness. Angle the same chisel with beveled edge downward. Make several cuts in the scored area, again to the depth of the hinge leaf. Remove wood chips with a chisel. Insert the hinge leaf to double check fit, but do not affix it to the door. Typically, doors taller than six feet require three hinges for weight distribution. Place the middle hinge halfway between the top and bottom hinges. Coat door edges with wood sealant. Use wood screws to attach hinge leaves to the new door. Hang new door. Placing the newly sealed door in the frame, insert the top and bottom pins. If the fit is acceptable, close the door and mark where the middle hinge falls on the door frame. If the old door had a middle hinge, the best case scenario would involve the new middle hinge falling in exactly the same place, necessitating no work on your part. If the middle hinge falls differently on the new door, take down the door by removing the bottom hinge pin and then the top. Use the hinge leaf as a template to outline the middle hinge’s location on the door frame. Cut the mortise in the same process used for door mortises. Attach the middle hinge to the door frame. Set the door in place and insert the hinge pins, working top to bottom. Another project for another day is installing a new lockset. For now, open your new door and go out and celebrate your accomplishment!

PRODUCTS

Do it Yourself Shopping Galore electrical fashion store comparison shopping, affiliate of selected stores comparing a range of products including, Books, DVD, Video Games, Popular Music, Classical Music, Electronics,Toys & Games, Digital Cameras Part of s-123.com Ltd Home Page Top of Page

Electrical Repair Headlines

Electrical fault delays trains (BBC Bristol)

An electrical fault on the railway line between Bristol Temple Meads and Bath Spa causes delays.

Expansion to follow move to town (Shropshire Star)

An electrical repair company has given Telford a big vote of confidence after relocating to the town from the Birmingham area. Control Electrics, which specialises in repairing controllers on electric vehicles, already has its sights set on expansion after moving into new premises at Horton Court, on the Hortonwood trading estate. Owner Shane … [visit site to [...]

Street race blamed for south Sacramento power outage (The Sacramento Bee)

Two teenagers face charges after their alleged street race resulted in a crash that knocked out power to thousands of SMUD customers Monday night and continued to interrupt electrical service today. SMUD crews restored power to the final 100 customers at 10:13 a.m. today, said Chris Capra, a SMUD public information officer. Those customers were among thousands without power overnight. Power ...

Unitil puts ice storm damage at $10m (New Hampshire Business Review)

Unitil Inc. estimates that it will incur $10 million in costs for replacement and repair of its electric distribution system in the wake of damage caused by the December ice storm, the Hampton, N.H.-based utility disclosed Monday in a filing with the U.S. Securities and Exchange Commission.

Brain pacemaker helps Parkinson's, but with risks (AP via Yahoo! News)

Parkinson's sufferers who had electrodes implanted in their brains improved substantially more than those who took only medicine, according to the biggest test yet of deep brain stimulation. The study, which followed patients for six months, offers the most hopeful news to date for Parkinson's sufferers. The new technique reduced tremors, rigidity and flailing of the limbs and allowed people to ...